American Megatrends PCE-5126 User Manual

User ManualPCE-5126LGA1155 Intel® Core™i7/i5/i3/Pentium®/Xeon® PICMG 1.3 Single Host Board with (ECC) DDR3 / Dual GbE LAN

PCE-5126 User Manual xB.14 SM Bus Connector (JFP2 / SNMP)... 79Table B.14:SM bus connector (JFP2

Chapter 11 Hardware Configuration

PCE-5126 User Manual 21.1 IntroductionPCE-5126 is a PICMG 1.3 form-factor single host board which is designed withIntel®B65/Q67/C206 PCH for indust

3 PCE-5126 User ManualChapter 1 Hardware Configuration1.3 Specifications1.3.1 System CPU: LGA1155-socket Core i7/i5/i3, Pentium and Xeon E3-12XX seri

PCE-5126 User Manual 41.3.3 Input/Output Backplane Support: Backplane Support Matrix Table: PCI bus: Four PCI masters to the backplane, 32-bit, 33 M

5 PCE-5126 User ManualChapter 1 Hardware Configuration1.4 Jumpers and ConnectorsConnectors on the PCE-5126 single host board link it to external devi

PCE-5126 User Manual 61.5 Board Layout: Jumper and Connector LocationsFigure 1.1 Jumper and connector locationsCPU1 CPU SocketDIMMA1 Memory connector

7 PCE-5126 User ManualChapter 1 Hardware Configuration1.6 PCE-5126 Block DiagramFigure 1.2 PCE-5126 block diagram

PCE-5126 User Manual 81.7 Safety Precautions1.8 Jumper SettingsThis section provides instructions on how to configure your motherboard by settingthe j

9 PCE-5126 User ManualChapter 1 Hardware Configuration1.8.2 BIOS CMOS/ME data clear (JCMOS1/JMECLR1)The PCE-5126 CPU card contains a jumper that can e

PCE-5126 User Manual iiCopyrightThe documentation and the software included with this product are copyrighted 2011by Advantech Co., Ltd. All rights ar

PCE-5126 User Manual 101.8.3 Watchdog timer output (JWDT1)The PCE-5126 contains a watchdog timer that will reset the CPU in the event theCPU stops pr

11 PCE-5126 User ManualChapter 1 Hardware Configuration1.10 Memory Installation ProceduresTo install DIMMs, first make sure the two ha ndles of the D

PCE-5126 User Manual 122. Remove the socket protection cap.3. Align the cuts on the processor with the edges of the socket.4. Replace the socket cap;

13 PCE-5126 User ManualChapter 1 Hardware Configuration5. Finished processor installation.1.13 Processor Cooler InstallationPurchasing PCE-5126's

PCE-5126 User Manual 14

Chapter 22 Connecting Peripherals

PCE-5126 User Manual 162.1 IntroductionYou can access most of the connectors from the top of the board. If you have a num-ber of cards installed, you

17 PCE-5126 User ManualChapter 2 Connecting Peripherals2.4 VGA Connectors (VGA1)The PCE-5126 has VGA outputs that can drive conventional CRT displays.

PCE-5126 User Manual 182.6 PS/2 Keyboard and Mouse Connector (KBMS1/KBMS2)Two on-board 6-pin mini-DIN connectors (KBMS1) provide connection to PS/2 ke

19 PCE-5126 User ManualChapter 2 Connecting Peripherals2.8 Front Panel Connectors (JFP1, JFP2 & JFP3)There are several external switches to monito

iii PCE-5126 User Manual Declaration of ConformityFCC Class ANote: This equipment has been tested and found to comply with the limits for a ClassA dig

PCE-5126 User Manual 202.8.2 External speaker (JFP2)JFP2 is a 4 -pin connector for an external speaker. The PCE-512 6 provides anonboard buzzer as an

21 PCE-5126 User ManualChapter 2 Connecting Peripherals2.9 H/W Monitor/Watchdog Timer/Infrared2.9.1 H/W Monitor Alarm (JOBS1)This 2-pin header is for

PCE-5126 User Manual 222.10 LAN Ports (LAN1 & LAN2)The PCE-5126 is equipped with one or two high-performance 1000 Mbps EthernetLANs. They are supp

23 PCE-5126 User ManualChapter 2 Connecting Peripherals2.11 High Definition Audio Module Interface (HDAUD1)This HDAUD1 pin header is the connection in

PCE-5126 User Manual 24Figure 2.1 Jumper and connector locations of PCA-AUDIO-HDA1ENote! Please remove the yellow jumper cap on the CPU card's HD

25 PCE-5126 User ManualChapter 2 Connecting Peripherals2.12 GPIO Header (GPIO1)Provides 14-Pin pin hea der for 8-bit Digital I/O usag e. Refer to App

PCE-5126 User Manual 262.14 Front Panel LAN Indicator Connector (LANLED1)Table 2.3: LAN LED IndicatorsLAN Mode LED1 LED21000Mbps Link On Green On On10

27 PCE-5126 User ManualChapter 2 Connecting Peripherals2.15 Serial ATA Interface (SATA1~SATA6)The PCE-5126 features high performance se rial ATA inter

PCE-5126 User Manual 28

Chapter 33 AMI BIOS Setup

PCE-5126 User Manual ivMemory CompatibilityPCE-5126 Memory Tested for Compatibility Brand Size Speed ECC

PCE-5126 User Manual 303.1 IntroductionAMIBIOS has been integrated into motherboards for over a decade. In the past, peo-ple often referred to the AMI

31 PCE-5126 User ManualChapter 3 AMI BIOS Setup3.2 Entering SetupTurn on the computer and check for the “patch” code. If there is a number assigned to

PCE-5126 User Manual 323.2.2 Advanced BIOS Features SetupSelect the Advanced tab from th e PCE-5126 setup screen to enter the AdvancedBIOS Setup scree

33 PCE-5126 User ManualChapter 3 AMI BIOS Setup3.2.2.1 Advantech BIOS Update V1.2Figure 3.4 Advantech BIOS Update V1.2You can update BIOS from UPDATE.

PCE-5126 User Manual 34 Enable Hibernation"Enable or disable" Hiber nate (OS/S4 Slee p State). This opt ion may not beeffective with some O

35 PCE-5126 User ManualChapter 3 AMI BIOS Setup3.2.2.4 CPU ConfigurationFigure 3.7 CPU ConfigurationFigure 3.8 Socket 0 CPU Information Active Proces

PCE-5126 User Manual 36 Limit CPUID MaximumSetting this item to [Enable] allows legacy operating systems to boot even with-out support for CPUs with

37 PCE-5126 User ManualChapter 3 AMI BIOS Setup Serial-ATA Controller 0This item appears only when you set the SATA Mode item to [IDE Mode]. Set to[E

PCE-5126 User Manual 383.2.2.7 Intel Trusted Execution Technology ConfigurationFigure 3.11 Intel Trusted Execution Technology Configuration Intel Tru

39 PCE-5126 User ManualChapter 3 AMI BIOS Setup Legacy USB SupportThis is for supporting USB device under legacy OS such as DOS. When choos-ing "

v PCE-5126 User Manual Specification ComparisonProcessor SupportBackplane Support Matrix TableModel Name Memory LAN VGA USB COMRemote ManagementPCE-51

PCE-5126 User Manual 403.2.2.10 Super IO ConfigurationFigure 3.14 Super IO ConfigurationFigure 3.15 Serial Port 1 Configuration

41 PCE-5126 User ManualChapter 3 AMI BIOS SetupFigure 3.16 Serial Port 2 ConfigurationFigure 3.17 Parallel Configuration Serial Port"Enable or D

PCE-5126 User Manual 423.2.2.11 PC Health StatusFigure 3.18 PC Health Status Case Open WarningEnable/Disable the Chassis Intrusion monitoring functi

43 PCE-5126 User ManualChapter 3 AMI BIOS Setup3.2.3 ChipsetFigure 3.19 Chipset3.2.3.1 North BridgeFigure 3.20 North Bridge Low MMIO AlignLow MMIO re

PCE-5126 User Manual 44 VT-dTo support Intel chipset virtualization technology for directed I/O. Initiate Graphic AdapterThis setting allows users t

45 PCE-5126 User ManualChapter 3 AMI BIOS Setup Restore AC Power Loss'Power Off, power On or Last State" to restore AC power loss SLP_S4

PCE-5126 User Manual 46 USB Port 1~14"Enable or Disable" USB Port 1~14.3.2.3.4 ME SubsystemFigure 3.23 ME Subsystem ME Subsystem"Enab

47 PCE-5126 User ManualChapter 3 AMI BIOS Setup3.2.3.5 Chipset Reference BoardFigure 3.24 Chipset Reference Board CIRA Trigger"Enable or Disable

PCE-5126 User Manual 48 Setup Prompt TimeoutUse the <+> and <-> keys to adjust the number of seconds to wait for setup acti-vation key.

49 PCE-5126 User ManualChapter 3 AMI BIOS Setup3.2.6 Save & ExitFigure 3.27 Save & ExitSave changes and exit*When you have completed system co

PCE-5126 User Manual viInitial InspectionBefore you begin installing your motherboard, please make sure that the followingmaterials have been shipped:

PCE-5126 User Manual 50Restore DefaultsSelect this option to restore BIOS configuration as origin.Save as User DefaultsSelect this option to save user

Chapter 44 Value-Added Software Services

PCE-5126 User Manual 524.1 Value-Added Software ServicesSoftware API: An interface th at defines the ways in which a n application programmay request

53 PCE-5126 User ManualChapter 4 Value-Added Software Services4.1.2 Software UtilityEmbedded Security IDThe embedded application is the most important

PCE-5126 User Manual 54

Chapter 55 Chipset Software Installation Utility

PCE-5126 User Manual 565.1 Before You BeginTo facilitate the installation of the enhanced display drivers and utility software, readthe instructions i

57 PCE-5126 User ManualChapter 5 Chipset Software Installation Utility5.3 Windows® XP / Windows® 7 Driver Setup1. Insert the driver CD into your syste

PCE-5126 User Manual 58

Chapter 66 Integrated Graphic Device Setup

vii PCE-5126 User Manual ContentsChapter 1 Hardware Configuration...11.1 Introduction ...

PCE-5126 User Manual 606.1 IntroductionThe Intel® LGA1155 CPUs have in tegrated graphics controllers. You need to installthe VGA driver to enable this

Chapter 77 LAN Configuration

PCE-5126 User Manual 627.1 IntroductionThe PCE-5126 has dual Gigabit Ethernet LANs via dedicated PCI Express x1 lanes(Intel 82579LM (LAN1) and 82583V

Chapter 88 SATA RAID Setup

PCE-5126 User Manual 648.1 IntroductionTo support demanding disk I/O, Intel Q67/C206 chipset integrates six Serial ATA con-trollers with software RAID

Appendix AA Programming the Watchdog Timer

PCE-5126 User Manual 66A.1 IntroductionThe PCE-5126’s watchdog timer can be used to monitor system software operationand take corrective action if the

67 PCE-5126 User ManualAppendix A Programming the Watchdog TimerTable A.1: Watchdog timer registersAddress of register (2E)AttributeRead/WriteValue (2

PCE-5126 User Manual 68A.1.3 Example program1. Enable watchdog timer and set 10 sec. as timeout interval;---------------------------------------------

69 PCE-5126 User ManualAppendix A Programming the Watchdog TimerOut dx,alInc dxMov al,10 ; 10 secondsOut dx,al ;---------------------------

PCE-5126 User Manual viii2.11 High Definition Audio Module Interface (HDAUD1) ... 23Figure 2.1 Jumper and connector locat

PCE-5126 User Manual 70Dec dx ; Lock NCT6776F Mov al,0aahOut dx,al3. Enable watchdog timer to be reset by mouse;----------------------

71 PCE-5126 User ManualAppendix A Programming the Watchdog TimerOut dx,alInc dxMov al,08hOut dx,al ;---------------------------------------

PCE-5126 User Manual 72Mov al,0f7hOut dx,al ;Write 1 to bit 5 of F7 register Inc dxIn al,dxOr al,20h Out dx,al ;-------------------------

Appendix BB I/O Pin Assignments

PCE-5126 User Manual 74B.1 Parallel Port Connector (LPT1)B.2 VGA Connector (VGA1)Table B.1: Parallel port connector (LPT1)Pin Signal Pin Signal1 STROB

75 PCE-5126 User ManualAppendix B I/O Pin AssignmentsB.3 RS 232 Serial Port (COM2)B.4 USB Header (USB12 ~ 78)Table B.3: RS-232 serial port (COM2)Pin S

PCE-5126 User Manual 76B.5 PS/2 Keyboard/Mouse Connector (KBMS1)B.6 External Keyboard Connector (KBMS2)B.7 CPU Fan Power Connector (CPUFAN1)Table B.5:

77 PCE-5126 User ManualAppendix B I/O Pin AssignmentsB.8 Power LED and Keyboard Lock Connector (JFP3 / PWR_LED & KEY LOCK)B.9 External Speaker Con

PCE-5126 User Manual 78B.11 HDD LED (JFP2 / HDDLED)B.12 ATX Soft Power Switch (JFP1 / PWR_SW)B.13 Hi-definition Audio Link Connector (HDAUD1) Table B.

79 PCE-5126 User ManualAppendix B I/O Pin AssignmentsB.14 SM Bus Connector (JFP2 / SNMP)B.15 LAN1 and LAN2 LED Connector (LANLED1)Table B.14: SM bus c

ix PCE-5126 User Manual 5.3 Windows® XP / Windows® 7 Driver Setup ... 57Chapter 6 Integrated Graphic Device

PCE-5126 User Manual 80B.16 GPIO Header (GPIO1)Table B.16: GPIO header (GPIO1)Pin Signal1SIO_GPIO02SIO_GPIO43SIO_GPIO14SIO_GPIO55SIO_GPIO26SIO_GPIO67S

81 PCE-5126 User ManualAppendix B I/O Pin AssignmentsB.17 System I/O PortsB.18 DMA Channel AssignmentsTable B.17: System I/O portsAddr. range (Hex) De

PCE-5126 User Manual 82B.19 Interrupt AssignmentsB.20 1st MB Memory MapB.21 PCI Bus MapTable B.19: Interrupt assignmentsPriority Interrupt# Interrupt

Appendix CC Programming the GPIO

PCE-5126 User Manual 84C.1 Supported GPIO RegisterBelow are the detailed descriptions of the GPIO addresses and programming sam-ple. C.2 GPIO register

85 PCE-5126 User ManualAppendix C Programming the GPIOINC DXMOV AL,07H ; Select logical device 7OUT DX,AL ;DEC DX MOV AL,E0H OUT DX,AL INC DXMOV AL

www.advantech.comPlease verify specifications before quoting. This guide is intended for referencepurposes only.All product specifications are subject